(分批公示特種設備無損檢測技術優秀論文的題目、作者和摘要。公示次序按電子稿接收排序） 【084】金屬材料相控陣檢測缺陷定位、定性、定量準確性分析與比較 李奎元 孔令昌 肖武華 (廣東省珠海市特種設備檢驗所，廣東 珠海 519002) 摘要：利用X射線檢測、常規超聲波檢測和超聲相控陣成像檢測系統對一厚度為30mm的對接焊縫試塊進行檢測。并對三種檢測方法的檢測結果進行缺陷定位、定性、定量準確性分析與比較。分析結果表明，超聲相控陣成像檢測系統在缺陷定位、定性、定量的準確性上具有獨特優勢，且具有操作方便、檢測快捷的特點。 關鍵詞：超聲波檢測；超聲相控陣成像檢測系統；扇形掃描；三角技術 【084】Abstract: Test a butt weld block of 30mm-thick by radiographic testing, ultrasonic testing and phased array ultrasonic flaw detector and recorder. Then analyse and compare the three testing results from flaw position, flaw type and flaw size. The analysis result shows that phased array ultrasonic flaw detector and recorder has unique advantage in the accuracy of flaw position, flaw type and flaw size. And the phased array ultrasonic flaw detector and recorder is more convennient for operation and more quick for testing. Key words: Ultrasonic testing; Phased array ultrasonic flaw detector and recorder; Sector scan; Delta technique 【085】遠場渦流檢測技術在電站鍋爐水冷壁管檢測中的應用 范賢振 倪進飛 黎 華 馬 括 （廣州市特種承壓設備檢測研究院，廣州 510100） 摘 要：電站鍋爐水冷壁管因磨損減薄導致爆管將影響鍋爐的安全運行。應用遠場渦流檢測技術可以發現水冷壁管上的磨損減薄缺陷。介紹了遠場渦流檢測技術的原理和工藝要點。采用高性能渦流檢測系統對電站鍋爐水冷壁管進行遠場渦流檢測，取得了較好的效果。 關鍵詞：遠場渦流檢測技術；水冷壁管；工藝 【085】Remote Field Eddy Current Testing for Water-Cooled Wall Tube of Plant Boiler FAN Xian-zhen NI Jin-fei LI Hua MA Kuo (Guangzhou Special Pressure Equipment Inspection and Research Institute， Guangzhou 510100， China ) Abstract： The blow-out of water-cooled wall tube of plant boiler due to thinning may affect the safe operation of the boiler. The remote field eddy current testing technique may be used to detect the defects. The theory and procedure of remote field eddy current testing technique were presented. High-performance eddy current inspection system was used to test the water-cooled wall tube, and good results were achieved. Key words：Remote field eddy current testing technique；Water-cooled wall tube；Procedure 【086】遠場渦流檢測技術在垃圾發電鍋爐水冷壁檢測的應用分析 （廣州市特種承壓設備檢測研究院，廣州 510100） 摘要:生活垃圾焚燒發電鍋爐水冷壁存在腐蝕凹坑、腐蝕減薄和疲勞裂紋等缺陷。本文闡述了在役生活垃圾焚燒發電鍋爐水冷壁采用遠場渦流檢測的適用性與優點，然后結合Ferroscope ? 308 遠場渦流管線內外壁檢測系統介紹垃圾發電鍋爐水冷壁采用遠場渦流的檢測工藝要點與實例。最后總結了遠場渦流檢測技術應用于生活垃圾焚燒發電鍋爐水冷壁檢測具有數據可靠性高、工作效率高和使用方便等優點。 關鍵詞：遠場渦流檢測 垃圾焚燒發電鍋爐 水冷壁檢測 WANG Xiao-Cong，LI Hua, LI Mao-Dong, CHEN Hong-Jun, NI Jun-Fei,FAN Xian-Zhen (Guangzhou Special Pressure Equipment Inspection and Research Institute, Guangzhou 510100) Abstract: Corrosion pit, corrosion thinning and fatigue crack appeared on the water cooled wall of municipal solid waste incineration plant boiler. The applicability and advantages of remote field eddy current testing apllying in municipal solid waste incineration plant boiler were presented in this paper, then the detecting process and applicative example of remote field eddy were introduced with Ferroscope ? 308 system. The advantage of high reliability, high efficiency and convenient to use is summarized in the last part. 【087】小波變換在聲發射信號特征提取中的應用方法研究 慶光蔚 王會方 （南京市特種設備安全監督檢驗研究院，南京 210002） 摘要：對聲發射信號進行分析與處理是目前獲取聲發射源信息的唯一有效途徑，也是聲發射技術發展的難點和瓶頸。針對聲發射信號的特點，本文對小波變換用于聲發射信號的特征提取問題進行了研究，總結出了適用于聲發射信號的小波變換信號特征提取方法，并對未來小波變換在聲發射領域的應用與研究方向進行了探討。 關鍵詞：聲發射 小波變換 特征提取 信號處理 【087】Extraction of Acoustic Emission Signal Features Based on Wavelet Transform Qing Guangwei Wang Huifang (Nanjing Special Equipment Inspection Institute，Nanjing 210002) Abstract：Acoustic emission signal processing is the only effective method to acquire the acoustic emission source information by now and also the bottleneck that affects its positive development. According to the characteristic of acoustic emission signal, a wavelet-based method of signal feature extraction was presented. The developing tendency of the application of wavelet transform in acoustic emission was discussed finally. Key word：Acoustic Emission（AE）；Wavelet Transform；Feature Extraction；Signal Processing 【088】用X射線衍射法測定焊接殘余應力 林進軍，愛派克測試技術(上海)有限公司 摘要:機械設備尤其是特種設備制造過程中普遍使用焊接技術，焊接過程中產生的殘余應力會導致應力腐蝕裂紋變形、疲勞裂紋、零件的過早失效以及過度設計。近年來X射線衍射法殘余應力測定技術的飛速發展，尤其是應力云圖技術的應用和便攜式應力測定設備的推廣，使得該技術在焊接殘余應力測定領域得到了越來越廣泛的運用。 X射線衍射法是一種無損的、非破壞性的殘余應力測定技術，該特點使其成為一種非常有效地表征焊接殘余應力特性、優化工藝及失效分析的工具，特別是能在零件焊接前、焊接后以及焊后處理過程中都能進行測量。 本文闡述了用X射線衍射法表征焊接殘余應力特性的重要性，并列舉了在不同類型焊接中殘余應力測定的應用實例，包括電弧焊、氬弧焊、電阻焊、激光焊和電子束焊接等。該技術也可以用來評估消除焊接殘余應力的一些工藝如研磨、熱處理和噴丸的效果等。 關鍵詞：焊接、殘余應力、X射線衍射 【089】對JB4730標準中無損檢測儀器設備校準或核查要求的修改建議 謝常歡 （深圳市特種設備安全檢驗研究院，廣東省，518029） 摘要:本文借鑒歐盟EN-04/15、香港HOKLAS 增補準則第15等標準中對無損檢測儀器設備校準或核查的要求，對今后新版JB4730標準中有關無損檢測儀器設備校準或核查的要求提出了修改建議。 關鍵詞:無損檢測儀器設備 校準 核查 【089】The Modification Suggestions For The Requirements of Calibration or Check of Non-Destructive Testing instruments for JB4730 Standard Xie Changhuan Shenzhen Institute of Special Equipment Inspection and Test , GuangDong Abstract:This article compare the requirements of Calibration or check for Non-Destructive Testing instruments with EN-04/15, HOKLAS Supplementary etc., it give the modification Suggestions For the requirements of Calibration or check of Non-Destructive Testing instruments for new JB4730 Standard. Key words:Non-Destructive Testing instruments calibration check 【090】無損檢測儀器設備內部校準的有效性 謝常歡 （深圳市特種設備安全檢驗研究院，廣東省，518029） 摘要:為確保無損檢測數據準確和結果可靠，規避無損檢測責任風險，應以量值溯源為基礎，對無損檢測儀器設備實施內部校準時，應保證內部校準的有效性。 關鍵詞:無損檢測儀器設備 量值溯源 內部校準 【091】無損檢測儀器設備校準或核查要求的探討 謝常歡 （深圳市特種設備安全檢驗研究院，廣東省，518029） 摘要:本文探討了無損檢測儀器設備校準或核查的要求，為無損檢測儀器設備量值溯源提出了對策，確保無損檢測數據準確和保證無損檢測結果可靠。 關鍵詞:無損檢測儀器設備 校準 核查 【091】The requirements of Calibration or check for Non-Destructive Testing instruments Xie Changhuan （Shenzhen Institute of Special Equipment Inspection and Test , GuangDong） Abstract:This article discuss the requirements of Calibration or check for Non-Destructive Testing instruments, it give the way to meet the traceability of Non-Destructive Testing instruments, help to ensure the accurate of Non-Destructive Testing data and assure the reliable of Non-Destructive Testing results . Key words:Non-Destructive Testing instruments calibration check 【092】小直徑厚壁管射線檢驗工藝優化 李光付 青島蘭石重型機械設備有限公司 摘要：根據標準要求，從透照工藝上各個方面分析小直徑厚壁管對接焊縫射線探傷的透照工藝。通過分析，結合實際選擇出合適的透照工藝，以獲得較好的底片質量。 關鍵字：小直徑 厚壁 管電壓 焦距 邊蝕效應 【092】Abstract: According to the standard requirement, from all aspects as technology through analysis of small diameter thick wall pipe butt weld X-ray detection through as process. Through the analysis, choose the right through as process, in order to achieve good film quality. Key word: Small diameter, thick wall, tube voltage, the focal length, the side effects of corrosion 【093】加楔塊超聲相控陣的聚焦特性測試 劉曉睿1、強天鵬2、鄔冠華1、孫忠波3、肖雄4、鄭凱2 1、南昌航空大學無損檢測技術教育部重點試驗室，南昌 330063 2、江蘇省特種設備安全監督檢驗研究院，南京 210003 3、天津誠信達金屬檢測有限公司，天津 300384 4、江蘇中特創業設備檢測有限公司，南京 210014 摘要：ASTM E2491-08為相控陣設備的測試提供了指導性規定。本文根據ASTM E2491-08，在安裝楔塊的情況下測試相控陣系統的聚焦能力，確定激發晶片數、聚焦深度以及偏轉角度對相控陣系統聚焦能力的影響。試驗采用ASTM E2491-08中規定的試塊，試驗激發的晶片數為8個、16個、32個，聚焦深度為10mm、50mm、100mm、150mm、200mm，聲束偏轉角度為35°、45°、60°和70°。通過試驗發現加裝楔塊后，大部分的近場區都在楔塊中，工件中的近場區很小。角度越小，工件中的近場區越大，隨著角度的增大，聚焦能力變弱。隨著聚焦晶片數量的增加，聚焦能力增強。隨著聚焦深度的增加，焦點尺寸增大。越接近楔塊物理主聲束，分辨率越好。 關鍵詞：超聲相控陣、聚焦、ASTM E2491-08 【093】The Test Of Focusing On Phased Array Ultrasonic With Wedge Liu Xiaorui1 Qiang Tianpeng2 Wu Guanhua1 XiaoXiong3Sun Zhongbo4ZhengKai2 1.Key Laboratory of Nondestructive Test （Ministry of Education）, Nanchang Hang Kong University Nanchang 330063, China 2.JiangSu Province Special Equipment Safety Supervision Inspection Institute Nanjing 210003，China 3.TianJin Chenxinda Metal-Testing Technology Co Ltd;Tianjin 300384;China 4.JiangSu Zhongtechuangye Equipment Inspection Co Ltd; Nanjing 210014; China Abstract：ASTM E2491-08 provides the standard guide for evaluating performance characteristics of phased array ultrasonic testing instruments and systems. In this paper，we use the phased array technology to measure the beam focusing capability of phased array ultrasonic with wedge according with ASTM E2491-08 so that we can identify the causes and effects of focusing capability in the factors such as the numbers of elements ,the focal depth and the scanning angle. In the test, the block designed in ASTM E2491-08 has been used, the elements used are 8,16 and 32,and the focal depths used are 10mm,50mm,100mm,150mm and 200mm,the scanning angles are 35°，45°，60°and 70°.Through the test, we can find that a large proportion of the near field is in the wedge and only a small proportion of the near field is in the block. The scanning angle is smaller ,the near field in the block is larger. And if the scanning angle increases, the focusing capability becomes weaker. The focusing capability intensify when the number of the elements increases. The focal depth increases, the focal spot size increases, too. The resolution of the system will be better if the scanning angle is close to the physical angle of the wedge. Keywords：Phased Array Ultrasonic; Focusing; ASTM E2491-08 | 
收藏
頂
踩
提升卡
置頂卡
沉默卡
喧囂卡
變色卡
千斤頂
顯身卡